working curve

Based on the analysis of the working principle of arc-cycloidal gear pump and the motion relationships parametric equation of a kind of cycloidal curve ot internal tooth was put forward, the trouble of processing and mapping when the rear damaged was solved.

对圆弧-摆线齿廓转子泵工作原理及运动关系进行分析的基础上.提出一种内转子摆线齿廓曲线的参数方程，解决了内转子加工以及损坏后难于测绘的难题。

The system model is the foundation of the following plan. Secondly, aimed at this problem about accumulated working hours, the algorithm of the cumulative curve of the work hours is put forward for the first time.

其次，分析了主计划系统中的工时累积问题，针对该问题，本文提出了工时累积曲线分析算法。

The optimal effective thermal efficiency working zone and optimal effective thermal efficiency curve are defined and compared with traditional internal combustion engine driving plunger pump.

定义了系统最佳有效热效率区和最佳有效热效率特性曲线并与传统内燃机驱动柱塞泵系统进行了比较。

In this article, working principle, composition of circuit and working characteristic curve are discussed.

文章论述了电动机软起动控制的工作原理, 控制电路组成,工作特性曲线.

The basic working principle of magnetic head is described, frequency response curve is given as gap-depletion expression, and gap-depletion is explained to be the main cause that the frequency response range of tape recorder is limited.

阐述了磁头的基本工作原理，绘制了磁头的频率响应曲线，给出了缝隙损耗的计算公式，揭示了重放磁头的缝隙损耗是造成磁记录的频率响应范围受到限制的主要原因。

In fourth chapter, firstly we analyze theory of curve saw working and give a theory, which approach NURBS by lines.

第四章中首先分析曲线带锯的锯切工艺，之后我们给出了用折线逼近NURBS的理论基础并且我们给出了误差分析。

Determination of the content of sodium in acylglycerol using atomic absorption spectrometry was described through selection of the sample dissolving time and solvent acidity, and comparison of the working curve method with standard addition method.

通过对溶样时间、酸度的选择，以及工作曲线法与标准加入法的比较，介绍了甘油脂中钠含量的测定方法。

Then the absorbance is calculated as concentration of AQ from working curve.

最后,根据工作曲线将吸光度转换成蒽醌浓度.

The constituent, working principle of AGC system and the spring curve of rolling mill were introduced. The reasons for variation of thickness deviation in longitudinal direction were analyzed in detail, and the corresponding solutions were put forword.

介绍了液压AGC控制系统的组成、工作原理及轧机的弹跳曲线，详细分析了带材在纵方向上造成厚差波动的原因，并提出解决方案。

The Cr~ ( 3+) standard solution is prepared from a potassium bichromate solution and the preparing procedure and the standard working curve are presented.

Cr3+标准溶液由重铬酸钾溶液制备，介绍了制备方法及标准曲线。

Satisfactory results are obtained with self-designed working curve, type standard and controlled samples.

采用用 自制 的工作曲线, 采取类型标准化及控样法取得较为满意的结果.

Design Method of Three-Roller Cold Rolling Bracket Working Curve of Titanium Alloy Tube

钛合金管材三辊冷轧机滑道工作曲线的设计方法

Confirmed the condition of anaLysis, the method of making working curve and quantifying suLfur in sampLe.

确定了仪器测试条件, 曲线制作方法,及测定样品的定量方法.